The Harvia LC-CV-VP RGBW LED controller is an electrical control component intended for compatible constant voltage LED lighting systems. Correct installation is essential for reliable operation and for protecting the connected equipment against electrical overload, incorrect wiring and unsuitable environmental conditions.
1. Confirm the correct controller type
Before installation, verify that the connected lighting uses constant voltage technology and is compatible with the LC-CV-VP. This model is intended for 12 V and 24 V RGBW LED strips.
The related LC-CC-VP model is designed for 350 mA constant current RGBW spotlights and has a different electrical specification. Constant voltage and constant current lighting equipment must not be connected interchangeably without explicit manufacturer approval.
2. Match the operating voltage
The controller supports 12 V and 24 V RGBW LED strip systems. The connected power supply must provide the voltage required by the LED strips. Mixing components designed for different voltages can damage the lighting equipment or prevent correct operation.
The installation should therefore be planned around one correctly matched electrical configuration. Before energising the system, verify the ratings of the power supply, controller and LED strips.
3. Observe the maximum rated output power
The LC-CV-VP has a specified maximum output power of 360 W. This rating represents an upper electrical limit and does not replace the need to calculate the actual load of the connected lighting.
The total LED strip consumption must remain within the permissible operating limits. In addition to the overall power rating, the maximum current and power permitted for each individual output channel must be observed according to the manufacturer's technical documentation.
The supplied product information does not specify individual channel current limits. These values must be verified in the official installation instructions before connecting high-power LED loads.
4. Connect the RGBW channels correctly
The controller provides four channels for RGBW lighting. Correct wiring is necessary to ensure that the red, green, blue and white lighting functions operate as intended.
Incorrect connections may cause unexpected colour behaviour or electrical faults. The terminal assignment, connection polarity and wiring arrangement must be checked against the manufacturer's connection diagram.
Electrical connections must only be made while the system is disconnected from its power source.
5. Pair the compatible remote control
The Harvia LC-CV-VP includes a dedicated button that makes pairing a compatible remote control easier. The manufacturer identifies the Sentiotec LED remote control as a suitable control accessory.
The exact pairing sequence should be performed according to the instructions supplied with the controller and remote control. Successful pairing should be verified before the controller is installed in a location that is difficult to access.
6. Select a suitable installation location
The controller must be installed in an environment that complies with its permitted operating conditions. Particular attention is required in sauna installations because temperatures and humidity levels can vary significantly between different mounting locations.
The supplied product information does not specify the controller's permissible ambient temperature, IP protection rating or minimum installation clearances. These technical limits must be obtained from the official manufacturer documentation before installation.
Do not assume that the controller is suitable for direct installation inside a hot sauna cabin simply because it is intended for use with sauna lighting equipment.
7. Use appropriate wiring and protection
The electrical installation must be designed for the expected current load. Suitable conductor dimensions, reliable terminals and appropriate circuit protection help reduce the risk of overheating and electrical faults.
Power supplies and other mains-connected equipment must be installed in accordance with applicable electrical regulations and manufacturer requirements. Where required, electrical work must be performed by a qualified electrician.
8. Check the system before commissioning
Before the first operation, inspect all connections and confirm that the power supply voltage, controller specifications and LED strip ratings match.
After switching on the system, verify that all four RGBW channels operate correctly and that the connected remote control responds as expected. The installation should also be checked for unusual heating, unstable lighting or other signs of incorrect electrical operation.
9. Observe the requirements of sauna environments
When the controller is used as part of a sauna lighting system, all connected components must be suitable for their respective installation locations. The temperature resistance of the LED strips, cables and mounting accessories must be considered independently of the controller specifications.
Lighting components installed near sauna heaters or other high-temperature areas require particular attention. Only equipment approved for the expected thermal conditions should be used.
10. Maintenance and long-term operation
The controller should be operated only within its specified electrical and environmental limits. If the lighting system develops faults, disconnect the power supply before inspecting the connections or replacing components.
Any modifications, repairs or changes to the electrical installation should be carried out in accordance with the manufacturer's requirements. Correct component selection and professional installation help maintain reliable operation throughout the service life of the lighting system.
Technical identification
Manufacturer: Harvia
Product code: LC-CV-VP
Type code: LC-CV-VP
Controller technology: Constant voltage
Supported LED voltage: 12 V / 24 V
Number of channels: 4
Lighting type: RGBW LED strips
Maximum rated power: 360 W
Compatible remote control: Sentiotec LED remote control
Finnish electrical product number: 4104901
